This article breaks down the YL105 datasheet in detail and explains exactly where, why, and how this sensor is than its more famous rivals. Part 1: What is the YL105? (A Datasheet Overview) Before we discuss "better," we need a baseline. The YL105 is a digital temperature and humidity sensor module. Unlike the raw DHT11, the YL105 comes pre-soldered onto a PCB with a built-in pull-up resistor and a filtering capacitor. Key Specifications from the YL105 Datasheet: | Parameter | Value | Why it matters | | :--- | :--- | :--- | | Operating Voltage | 3.3V to 5.5V | Better compatibility (works with 3.3V ESP32 & 5V Arduino) | | Humidity Range | 20% to 90% RH | Standard room conditions | | Humidity Accuracy | ±5% RH | Comparable to DHT11 | | Temperature Range | 0°C to 50°C | Indoor/Greenhouse focused | | Temperature Accuracy | ±2°C | Adequate for HVAC monitoring | | Sampling Rate | 1 Hz (1 reading per second) | Better stability than cheap clones | | Signal Type | Single-bus digital | Uses only 1 GPIO pin |
It respects the 20ms start signal and uses a 30µs threshold (midpoint between bit0's 26µs and bit1's 70µs). Most libraries incorrectly use 40µs, causing bit errors at the edges of the tolerance range. Part 6: Common Pitfalls (What the Datasheet Doesn't Explicitly Say) The YL105 datasheet is good, but it misses three practical details. Knowing these makes your usage better than 90% of other engineers. 1. Power Supply Noise The datasheet mentions "VDD ripple < 50mV." In reality, if you power the YL105 from the same 5V rail as a servo motor, you will get +10% RH errors. Better solution: Use a dedicated 3.3V LDO regulator or add a 470µF capacitor on the power rail. 2. Self-Heating If you read the YL105 faster than 1 Hz (e.g., every 500ms), the internal thermistor will self-heat by 2-3°C. The datasheet does not warn about this clearly. Better practice: Limit reads to once every 2 seconds for temperature accuracy, even if humidity can refresh faster. 3. Condensation Recovery The datasheet says "non-condensing environment." But if condensation occurs, the sensor requires 2 hours of drying at 50°C. Better design: Mount the YL105 vertically, not horizontally, so water drips off the PCB. Part 7: Conclusion – Is the YL105 "Better" for YOU? After reading this deep dive into the yl105 datasheet better analysis, ask yourself:
In the crowded world of capacitive humidity sensors, the YL105 is often misunderstood. Viewed by beginners as a "cheap alternative," this sensor module—when paired with a correct reading of its datasheet—offers a superior price-to-performance ratio for 80% of DIY and commercial IoT projects.
The YL105 datasheet reveals a sensor that is better for 80% of hobbyist and commercial indoor projects . It is robust, forgiving, and cheap. When paired with proper timing code and a clean power supply, it rivals sensors twice its price.
This article breaks down the YL105 datasheet in detail and explains exactly where, why, and how this sensor is than its more famous rivals. Part 1: What is the YL105? (A Datasheet Overview) Before we discuss "better," we need a baseline. The YL105 is a digital temperature and humidity sensor module. Unlike the raw DHT11, the YL105 comes pre-soldered onto a PCB with a built-in pull-up resistor and a filtering capacitor. Key Specifications from the YL105 Datasheet: | Parameter | Value | Why it matters | | :--- | :--- | :--- | | Operating Voltage | 3.3V to 5.5V | Better compatibility (works with 3.3V ESP32 & 5V Arduino) | | Humidity Range | 20% to 90% RH | Standard room conditions | | Humidity Accuracy | ±5% RH | Comparable to DHT11 | | Temperature Range | 0°C to 50°C | Indoor/Greenhouse focused | | Temperature Accuracy | ±2°C | Adequate for HVAC monitoring | | Sampling Rate | 1 Hz (1 reading per second) | Better stability than cheap clones | | Signal Type | Single-bus digital | Uses only 1 GPIO pin |
It respects the 20ms start signal and uses a 30µs threshold (midpoint between bit0's 26µs and bit1's 70µs). Most libraries incorrectly use 40µs, causing bit errors at the edges of the tolerance range. Part 6: Common Pitfalls (What the Datasheet Doesn't Explicitly Say) The YL105 datasheet is good, but it misses three practical details. Knowing these makes your usage better than 90% of other engineers. 1. Power Supply Noise The datasheet mentions "VDD ripple < 50mV." In reality, if you power the YL105 from the same 5V rail as a servo motor, you will get +10% RH errors. Better solution: Use a dedicated 3.3V LDO regulator or add a 470µF capacitor on the power rail. 2. Self-Heating If you read the YL105 faster than 1 Hz (e.g., every 500ms), the internal thermistor will self-heat by 2-3°C. The datasheet does not warn about this clearly. Better practice: Limit reads to once every 2 seconds for temperature accuracy, even if humidity can refresh faster. 3. Condensation Recovery The datasheet says "non-condensing environment." But if condensation occurs, the sensor requires 2 hours of drying at 50°C. Better design: Mount the YL105 vertically, not horizontally, so water drips off the PCB. Part 7: Conclusion – Is the YL105 "Better" for YOU? After reading this deep dive into the yl105 datasheet better analysis, ask yourself: yl105 datasheet better
In the crowded world of capacitive humidity sensors, the YL105 is often misunderstood. Viewed by beginners as a "cheap alternative," this sensor module—when paired with a correct reading of its datasheet—offers a superior price-to-performance ratio for 80% of DIY and commercial IoT projects. This article breaks down the YL105 datasheet in
The YL105 datasheet reveals a sensor that is better for 80% of hobbyist and commercial indoor projects . It is robust, forgiving, and cheap. When paired with proper timing code and a clean power supply, it rivals sensors twice its price. The YL105 is a digital temperature and humidity
Unlock unlimited access to all WTR content